# 18V 5A H-Bridge breakout board
* For driving **DC motors**, **coils** or other inductive loads
* **Bi-directional** output control
* Input **3.0-18V**
* Output **up to 5A continuous**, up to 9A pulse
* Works with **1.8V to 6.0V logic** level inputs
* Overcurrent protection
* Short circuit protection
* Overheat protection
* Integrated flyback diodes
* Pretty idiot-proof
* Uses CP2119L or TMI8260SP integrated circuit


# Basic operation
![](images/usage.jpg)
* Logic HIGH on the FORWARD pin makes the motor spin **FORWARD** (M+ becomes VIN, M- becomes GND)
* Logic HIGH on the REVERSE pin makes the motor spin **REVERSE** (M+ becomes GND, M- becomes VIN)
* Logic HIGH on BOTH pins makes the motor ACTIVELY **BREAK** (M+ becomes GND, M- becomes GND)
* Logic LOW on BOTH pins makes the motor **FREESPIN** (M+ floats, M- floats)

## "Analog" control
* The power of the motor can be precisely adjusted (0-100%) by applying a PWM SQUARE WAVE to the FORWARD/REVERSE pins
* Recommended PWM frequency: 100Hz - 5KHz
* "analogWrite()" on Arduino produces a suitable 490Hz square wave with 255 levels of control


# PCB assembly / component configurations

## For Voltage 3-18V and Current 0-5A (basic configuration)
![](images/soldering.jpg)
* Populate the TMI8260 (duh!). Note where pin 1 (marked) goes!
* Populate '2x10uF' with included ceramic capacitors
* Populate '220uF' with included polymer aluminium capacitor. Note where the negative goes!
* Skip the additional flyback diodes
* This works with PWM frequencies up to 5KHz

## For PWM frequency > 5KHz
* If the expected current is low (<3A), you can probably just use the basic configuration
* Otherwise, add 4x flyback diodes on the PCB
* SS54 or SS34 diodes, in SOD-123L package
* They are difficult to solder, sorry!

## For Voltage<10V AND Current<2A:
If you don't need the high power of this chip, consider using the DRV8835 module instead. It is cheaper and comes pre-assembled.

## For ONE directional control:
If you don't need bi-directional control, consider just using a N-MOSFET and flyback diode instead. Cheaper, simpler.


# Built in protections
The TMI8260/CP2119 has protection features that allow it to protect **ITSELF**
* It cannot protect the connected motor/coil - make sure VIN is a voltage that the motor can handle!
* It cannot fully protect the power source - make sure it can handle the current the motor will take!

## Overcurrent / short-circuit protection
* If the connected motor / coil attempts to take more than > 9A, overcurrent protection kicks in
* The device will stop supplying power for approx 50 microseconds, and let the current drop
* After that, the device will automatically retry applying current
* This is very helpful when starting large motors from a standstill - the surge current will be effectively limited, and the motor will slowly spin up instead of taking infinity amperes.
* This does protect the power source by limiting the consumed current to approx 9A
* This feature relies on the inductance of the connected motor/coil. If the inductance is too low, the safety feature will not have time to react before the current becomes too high.

## Overtemperature protection
* If the TMI8260 gets too hot (>150C) during continuous operation, it will temporarily stop providing power to the load
* After cooling down, it will automatically return to normal operation

## Integrated flyback diodes
* Inductive loads tend to induct reverse voltages that may damage drive circuitry
* The TMI8260 has integrated flyback diodes (inside the chip) that can handle most use cases
* The PCB has space for additional external flyback diodes, for more extreme cases (see "Use cases")

# Parts included in the kit:
![](images/content.jpeg)
* Breakout PCB
* TMI8260SP-MS chip
* Polymer aluminium capacitor (SHENGYANG SM227M025E0600 220uF 25V)
* 3x Ceramic capacitors (10uF 25V 0603)


# Documentation
![Schematic](images/schematic.png)
![PCB](image/pcb.png)
[TMI8260SP-MS datasheet (in Chinese)](datasheets/TMI8260SP-MS.pdf)


# Future improvements
### Thermal management
![](images/thermal.jpeg)
* Most of the heat from the IC seems to be dissipating though the OUT1 / OUT2 pins
* Therefore, the OUT1 / OUT2 polygons should be enlarged, for better cooling
* Maybe the IC should be moved more towards the middle of the board
* Right now the board can barely handle 5A

### Solderability
* The large cap is very difficult to solder
	* Some thermal reliefs can make it much easier, while probably not impacting performance in any significant way
* The optional flyback diodes are difficult to solder
	* The footprint should be made hand-solderable (by enlarging the pad by a lot)

---
Made at [ELAB](http://elab.kth.se) by Marek Baczynski. Find him on the ELAB slack if you have any questions